It’s a SNAP Magnetic Boat Cushion Fasteners FAQs

Question 1

What are magnetic boat cushion snaps?

Accepted Answer

Magnetic boat cushion snaps are fastening devices that use high-strength magnets instead of traditional snap studs. One magnet fits into the cushion and the other attaches to the boat’s seating surface. When the cushion is dropped into place, the magnets align and hold it securely without requiring force to press snaps together.

Question 2

What comes in the Gen 2 Pro Magnet 12 Pack?

Accepted Answer

The Gen 2 Pro Magnet 12 Pack contains twelve pairs of magnetic fasteners. Each pair includes a cushion-side magnet, Magnet A, and a deck-side magnet, Magnet C, along with installation hardware. The hardware consists of marine-grade stainless-steel screws and protective caps and washers.

Question 3

What materials are used in It’s a SNAP fasteners, and are they made for marine use?

Accepted Answer

It’s a SNAP fasteners use high-strength neodymium magnets that are nickel-coated for corrosion resistance. The mounting hardware is marine-grade stainless steel and comes with protective poly caps and vinyl washers. The product is specifically designed for marine environments.

Question 4

Will It’s a SNAP work with my boat cushions?

Accepted Answer

Yes. It’s a SNAP is retrofit-friendly and compatible with many existing cushion setups, including those on center consoles, pontoons, cruisers, and yachts. Compatibility depends on factors such as cushion hardware, alignment, and the condition of your seating surfaces. Inspect your setup and remove old snaps before installing to ensure a flush fit.

Question 5

Are It’s a SNAP magnets waterproof?

Accepted Answer

The magnets are corrosion resistant, but they are not fully waterproof. While the nickel coating helps protect them, long-term exposure to moisture can lead to corrosion. For best performance, keep the magnets dry when possible and use marine-grade silicone during installation on fiberglass.

Question 6

How long do It’s a SNAP magnets last?

Accepted Answer

The fasteners are designed for a five-to-seven-year lifespan in typical marine environments. With proper care, such as rinsing after saltwater use, avoiding prolonged exposure to extreme heat, and inspecting hardware regularly, the magnets can provide dependable performance for many years.

Question 7

Is It’s a SNAP easy to install?

Accepted Answer

Yes. The system is designed for quick and simple installation. Magnet A snaps into the cushion, and Magnet C attaches to the boat’s surface with screws. This makes the process straightforward for both DIY boat owners and professional installers.

Question 8

Do I need special tools to install It’s a SNAP?

Accepted Answer

No special tools are necessary. A basic screwdriver is usually sufficient to secure the magnets with the included hardware. For fiberglass installations, using a drill to create pilot holes and adding a bead of marine-grade silicone is recommended.

Question 9

What are Magnet A and Magnet C?

Accepted Answer

Magnet A is the cushion-side component that replaces the female part of a traditional snap and fits into the cushion. Magnet C is the deck-side component that replaces the male stud on the boat’s surface. Magnet C is countersunk to accept standard marine screws, enabling a secure and flush installation.

Question 10

What should I do before installing It’s a SNAP?

Accepted Answer

Inspect your cushions and seating surfaces, remove any existing snaps, and ensure the mounting areas are clean. Install all Magnet A components into the cushions first, as this completes much of the work quickly. Check for wear or corrosion on the original hardware and address any issues so the magnets sit flush.

Question 11

Can I install It’s a SNAP on fiberglass?

Accepted Answer

Yes. It’s a SNAP can be installed on fiberglass surfaces. Avoid drilling through the deck or into areas that could interfere with hatches. Add a bead of marine-grade silicone when installing Magnet C on fiberglass to protect the magnet and ensure long-lasting performance.

Question 12

What should I check after installing It’s a SNAP?

Accepted Answer

Verify that all magnet assemblies sit flush and that screws are snug but not overtightened. Boat vibrations may loosen hardware over time, so recheck the screws after your first few outings and periodically thereafter. Ensure magnets are free of debris and maintain a flush connection for the best hold.

Question 13

How should I safely handle It’s a SNAP magnets during installation?

Accepted Answer

The magnets are extremely strong. Keep them at least 24 inches apart during handling to prevent them from snapping together unexpectedly. Handle one magnet at a time and avoid placing body parts between them. Because the magnets are brittle, they can chip, crack, or shatter if they collide.

Question 14

Can children handle It’s a SNAP magnets?

Accepted Answer

No. The magnets are not toys and should not be handled by children. Small magnets pose a choking hazard and, if swallowed, can attract through intestinal walls and cause serious injury.

Question 15

Can It’s a SNAP magnets affect pacemakers or medical devices?

Accepted Answer

Yes. The strong magnetic fields can interfere with pacemakers, defibrillators, and other implanted medical devices. Individuals with these devices should keep the magnets away and consult a physician if they have any concerns.

Question 16

Can magnets affect electronics or cards?

Accepted Answer

Yes. Strong magnets can damage magnetic media such as credit cards, identification cards, and hard drives. They can also affect certain electronic devices and displays. Keep the magnets away from electronic devices and magnetic storage media.

Question 17

How should I care for magnetic boat cushion fasteners?

Accepted Answer

Rinse the fasteners with fresh water and mild soap after exposure to saltwater. Wipe magnet faces and mating surfaces clean to remove any sand, salt, or debris that could reduce holding power. Inspect hardware regularly to make sure screws remain snug and magnets sit flush.

Question 18

Can It’s a SNAP make boat cushions easier to remove?

Accepted Answer

Yes. One of the main benefits of the system is that cushions drop into place and lift off easily without the struggle associated with mechanical snaps. This makes it quicker to set up seating and remove cushions for cleaning or storage.

Question 19

Can It’s a SNAP help with corroded or hard-to-use boat snaps?

Accepted Answer

Yes. It’s a SNAP replaces traditional snap hardware that may be corroded, frozen, or misaligned. By eliminating mechanical snaps, it removes the most common causes of sticking and jamming and uses corrosion-resistant materials for improved durability.

Question 20

Where can I buy It’s a SNAP?

Accepted Answer

You can purchase It’s a SNAP products directly through the company’s online store at https://itsasnap.us/. The Gen 2 Pro Magnet 12 Pack and other products are available on the site.

Question 21

How long does shipping take, and will I receive tracking information?

Accepted Answer

Orders are usually processed within two to three business days. Standard shipping typically takes five to seven business days, while expedited shipping can take two to three business days. Once your order ships, the company will email you a tracking number so you can monitor the delivery.

Question 22

Does It’s a SNAP ship internationally?

Accepted Answer

Currently, It’s a SNAP ships only within the United States. Customers outside the U.S. should contact the company directly to inquire about international shipping options.

Question 23

What is the return, exchange, and damaged order policy?

Accepted Answer

All sales are final. Returns, exchanges, and cancellations are not accepted after purchase. If your order arrives damaged, defective, or incorrect, contact the company with a description and photos of the issue. Approved refunds will be issued to the original payment method.

Question 24

Where is It’s a SNAP available?

Accepted Answer

It’s a SNAP serves boating communities across the United States, with a focus on regions in New Jersey, Florida, New York, and Connecticut. The company provides fasteners for a wide variety of vessels, including center consoles, pontoons, cruisers, and yachts.

Question 25

Can I order It’s a SNAP if my town is not listed?

Accepted Answer

Yes. The listed service areas are examples only. It’s a SNAP is available to boaters nationwide through online ordering, even if your specific town is not mentioned.

Question 26

Can boaters in New Jersey, Florida, New York, and Connecticut order It’s a SNAP?

Accepted Answer

Yes. Boaters in these states can order directly through the website. Towns and regions throughout New Jersey, Florida, New York, and Connecticut are specifically noted as service areas, but customers anywhere in the United States can order the product.

Your cart is empty

Your cart

Estimated total

Installation

Click the video below to watch our short demo on how to install your new It's A SNAP magnets!

Installation Tips

12-Pack

6-Pack

12-Pack

6-Pack

Country/region

Installation

Click the video below to watch our short demo on how to install your new It's A SNAP magnets!

Installation Tips